大家好，欢迎来到IT知识分享网。
实验目的：
l配置交换机的基本命令
实验说明：
Cisco的交换机配置命令和Router的配置命令基本一致, 故这里不做详细介绍
实验拓扑图：
实验步骤：
1. 了解基本配置
|
Sw1#configure terminal Sw1(config)# interface fastethernet0/10 Sw1(config-if)#speed 10 Sw1(config-if)#duplex half Sw1(config-if)#description test Sw1(config-if)#end Sw1#sh int f0/10 status Port Name Status Vlan Duplex Speed Type Fa0/10 test notconnect 1 half 10 10/100BaseTX Sw1#sh int fa0/11 FastEthernet0/11 is up, line protocol is up Hardware is Fast Ethernet, address is 000d.2960.8bcb (bia 000d.2960.8bcb) MTU 1500 bytes, BW Kbit, DLY 1000 usec, reliability 255/255, txload 1/255, rxload 1/255 Encapsulation ARPA, loopback not set Keepalive set (10 sec) Full-duplex, 100Mb/s input flow-control is off, output flow-control is off ARP type: ARPA, ARP Timeout 04:00:00 Last input 00:00:00, output 00:00:01, output hang never Last clearing of “show interface” counters never Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: fifo Output queue :0/40 (size/max) 5 minute input rate 0 bits/sec, 0 packets/sec 5 minute output rate 0 bits/sec, 0 packets/sec 5751 packets input, bytes, 0 no buffer Received 5680 broadcasts, 0 runts, 0 giants, 0 throttles 0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored 0 watchdog, 5680 multicast, 0 pause input 0 input packets with dribble condition detected 119 packets output, 12781 bytes, 0 underruns 0 output errors, 0 collisions, 2 interface resets 0 babbles, 0 late collision, 0 deferred 0 lost carrier, 0 no carrier, 0 PAUSE output 0 output buffer failures, 0 output buffers swapped out Sw1#sh int fa0/1 switchport Name: Fa0/1 Switchport: Enabled Administrative Mode: dynamic desirable Operational Mode: down Administrative Trunking Encapsulation: dot1q Negotiation of Trunking: On Access Mode VLAN: 1 (default) Trunking Native Mode VLAN: 1 (default) Administrative private-vlan host-association: none Administrative private-vlan mapping: none Operational private-vlan: none Trunking VLANs Enabled: ALL Pruning VLANs Enabled: 2-1001 Protected: false Voice VLAN: none (Inactive) Appliance trust: none Sw1#sh run int f0/1 Building configuration… Current configuration : 89 bytes ! interface FastEthernet0/1 description test no ip address duplex half speed 10 end Sw1#show version Cisco Internetwork Operating System Software IOS ™ C2960 Software (C2960-I6Q4L2-M), Version 12.2(11)EA1, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Wed 28-Aug-02 10:25 by antonino Image text-base: 0x, data-base: 0x ROM: Bootstrap program is CALHOUN boot loader Sw1 uptime is 30 minutes System returned to ROM by power-on System image file is “flash:/c2960-i6q4l2-mz.122-11.EA1.bin” cisco WS-C2960-24 (RC32300) processor (revision J0) with 20402K bytes of memory. Processor board ID FOC0725Y05M Last reset from system-reset Running Standard Image 24 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:0D:29:60:8B:C0 Motherboard assembly number: 73-5782-11 Power supply part number: 34-0965-01 Motherboard serial number: FOC07250XZ2 Power supply serial number: DAB07226HJ0 Model revision number: J0 Motherboard revision number: A0 Model number: WS-C2960-24 System serial number: FOC0725Y05M Configuration register is 0xF Sw1(config)#do sh vlan b VLAN Name Status Ports —- ——————————– ——— ——————————- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10（省略） 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active Sw1#sh int trunk Port Mode Encapsulation Status Native vlan Fa0/11 desirable 802.1q trunking 1 Fa0/12 desirable 802.1q trunking 1 Port Vlans allowed on trunk Fa0/11 1-4094 Fa0/12 1-4094 Port Vlans allowed and active in management domain Fa0/11 1 Fa0/12 1 Port Vlans in spanning tree forwarding state and not pruned Fa0/11 1 Fa0/12 none Sw1(config)#vlan 20 Sw1(config-vlan)#name G-LAB20 Sw1(config-vlan)#end Sw1#vlan database Sw1(vlan)#vlan 30 name G-LAB30 VLAN 30 added: Name: G-LAB30 Sw1(vlan)#exit APPLY completed. Exiting…. Sw1# Sw1#show vlan brief VLAN Name Status Ports —- ——————————– ——— ——————————- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10 20 G-LAB20 active 30 G-LAB30 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active Sw1# Sw1(config)#no vlan 30 Sw1(config)#do sh vlan b VLAN Name Status Ports —- ——————————– ——— ——————————- 1 default active Fa0/1, Fa0/2, Fa0/3, Fa0/4 Fa0/5, Fa0/6, Fa0/7, Fa0/8 Fa0/9, Fa0/10 20 G-LAB20 active 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active Sw1(config)#int fa0/1 Sw1(config-if)#switchport mode access Sw1(config-if)#switchport access vlan 20 Sw1(config-if)#spanning-tree portfast %Warning: portfast should only be enabled on ports connected to a single host. Connecting hubs, concentrators, switches, bridges, etc… to this interface when portfast is enabled, can cause temporary bridging loops. Use with CAUTION %Portfast has been configured on FastEthernet0/1 but will only have effect when the interface is in a non-trunking mode. Sw1(config-if)#exit Sw1(config)#vlan 30 Sw1(config-vlan)#name G-LAB30 Sw1(config-vlan)#exit Sw1(config)#int range fa0/2 – 5 Sw1(config-if-range)#sw mode access Sw1(config-if-range)#sw access vlan 30 Sw1(config-if-range)#end Sw1#sh vlan brief VLAN Name Status Ports —- ——————————– ——— ——————————- 1 default active Fa0/6, Fa0/7, Fa0/8, Fa0/9 Fa0/10 20 G-LAB20 active Fa0/1 30 G-LAB30 active Fa0/2, Fa0/3, Fa0/4, Fa0/5 1002 fddi-default active 1003 token-ring-default active 1004 fddinet-default active 1005 trnet-default active Sw1(config-if)#int vlan 30 Sw1(config-if)# Sw1(config-if)#ip address 192.168.30.254 255.255.255.0 Sw1(config-if)#no shutdown Sw1(config-if)#exit Sw1(config)#line vty 0 4 Sw1(config-line)#password G-LAB Sw1(config-line)#login Sw1(config)#enable secret G-LAB123 Sw1(config)#end |
2. 简单验证
1) PC1 IP:192.168.30.23/24
PC2 IP:192.168.30.24/24
2) PC1 连结到Sw1的Fa0/1端口，PC2 连结到Sw1的Fa0/2端口，观察两个端口指示灯变成绿色的时间：
Fa0/1: ___s
Fa0/2: ___s
3） PC1 ping PC2：
|
C:\Documents and Settings\Joseph>ping 192.168.30.24 Pinging 192.168.30.24 with 32 bytes of data: Request timed out. Request timed out. Request timed out. Request timed out. Ping statistics for 192.168.30.24: Packets: Sent = 4, Received = 0, Lost = 4 (100% loss), |
4） 将PC1 连结到Sw1的Fa0/3端口，PC1 再ping PC2：
|
C:\Documents and Settings\Joseph>ping 192.168.30.24 Pinging 192.168.30.24 with 32 bytes of data: Request timed out. Reply from 192.168.30.24: bytes=32 time=1ms TTL=64 Reply from 192.168.30.24: bytes=32 time=1ms TTL=64 Reply from 192.168.30.24: bytes=32 time=1ms TTL=64 Ping statistics for 192.168.30.24: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 1ms, Average = 1ms C:\Documents and Settings\Joseph>telnet 192.168.30.254 Trying 192.168.30.254 … Open User Access Verification Password: Sw1>en Password: Sw1# Sw1#copy run start Destination filename [startup-config]? Building configuration… Sw1# Sw1#sh flash: Directory of flash:/ 2 -rwx Mar 01 1993 00:03:19 c2960-i6q4l2-mz.122-11.EA1.bin 3 -rwx 556 Mar 01 1993 03:56:53 vlan.dat 4 -rwx 269 Jan 01 1970 00:01:16 env_vars 5 -rwx 974 Mar 01 1993 03:59:06 config.text 6 -rwx 5 Mar 01 1993 03:59:06 private-config.text 7 drwx 704 Mar 01 1993 00:03:55 html 19 -rwx 109 Mar 01 1993 00:03:56 info 20 -rwx 109 Mar 01 1993 00:03:56 info.ver Sw1#delete flash:/vlan.dat Delete filename [vlan.dat]? Delete flash:/vlan.dat? [confirm]↙ Sw1#delete flash:/config.text Delete filename [config.text]? Delete flash:/config.text? [confirm]↙ Sw1#sh flash: Directory of flash:/ 2 -rwx Mar 01 1993 00:03:19 c2960-i6q4l2-mz.121-11.EA1.bin 4 -rwx 269 Jan 01 1970 00:01:16 env_vars 6 -rwx 5 Mar 01 1993 03:59:06 private-config.text 7 drwx 704 Mar 01 1993 00:03:55 html 19 -rwx 109 Mar 01 1993 00:03:56 info 20 -rwx 109 Mar 01 1993 00:03:56 info.ver bytes total ( bytes free) Sw1#reload Proceed with reload? [confirm]↙ 04:06:33: %SYS-5-RELOAD: Reload requested C2960 Boot Loader (C2960-HBOOT-M) Version 12.2(11r)EA1, RELEASE SOFTWARE (fc1) Compiled Mon 22-Jul-02 17:18 by antonino WS-C2960-24 starting… Base ethernet MAC Address: 00:0d:29:60:8b:c0 Xmodem file system is available. Initializing Flash… flashfs[0]: 16 files, 2 directories flashfs[0]: 0 orphaned files, 0 orphaned directories flashfs[0]: Total bytes: flashfs[0]: Bytes used: flashfs[0]: Bytes available: flashfs[0]: flashfs fsck took 6 seconds. …done initializing flash. Boot Sector Filesystem (bs:) installed, fsid: 3 Parameter Block Filesystem (pb:) installed, fsid: 4 Loading “flash:/c2960-i6q4l2-mz.122-11.EA1.bin”…######################################################################################################################################################################################################################################################################################### File “flash:/c2960-i6q4l2-mz.121-11.EA1.bin” uncompressed and installed, entry point: 0x executing… Restricted Rights Legend Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph (c) of the Commercial Computer Software – Restricted Rights clause at FAR sec. 52.227-19 and subparagraph (c) (1) (ii) of the Rights in Technical Data and Computer Software clause at DFARS sec. 252.227-7013. cisco Systems, Inc. 170 West Tasman Drive San Jose, California 95134-1706 Cisco Internetwork Operating System Software IOS ™ C2960 Software (C2960-I6Q4L2-M), Version 12.2(11)EA1, RELEASE SOFTWARE (fc1) Copyright (c) 1986-2007 by cisco Systems, Inc. Compiled Wed 28-Aug-02 10:25 by antonino Image text-base: 0x, data-base: 0x Initializing flashfs… flashfs[1]: 16 files, 2 directories flashfs[1]: 0 orphaned files, 0 orphaned directories flashfs[1]: Total bytes: flashfs[1]: Bytes used: flashfs[1]: Bytes available: flashfs[1]: flashfs fsck took 7 seconds. flashfs[1]: Initialization complete. Done initializing flashfs. POST: System Board Test : Passed POST: Ethernet Controller Test : Passed ASIC Initialization Passed POST: FRONT-END LOOPBACK TEST : Passed cisco WS-C2960-24 (RC32300) processor (revision J0) with 20402K bytes of memory. Processor board ID FOC0725Y05M Last reset from system-reset Running Standard Image 12 FastEthernet/IEEE 802.3 interface(s) 32K bytes of flash-simulated non-volatile configuration memory. Base ethernet MAC Address: 00:0D:29:60:8B:C0 Motherboard assembly number: 73-5782-11 Power supply part number: 34-0965-01 Motherboard serial number: FOC07250XZ2 Power supply serial number: DAB07226HJ0 Model revision number: J0 Motherboard revision number: A0 Model number: WS-C2960-24 System serial number: FOC0725Y05M — System Configuration Dialog — Would you like to enter the initial configuration dialog? [yes/no]: no↙ Press RETURN to get started! Switch> |
3. 实验完成
免责声明：本站所有文章内容,图片，视频等均是来源于用户投稿和互联网及文摘转载整编而成，不代表本站观点，不承担相关法律责任。其著作权各归其原作者或其出版社所有。如发现本站有涉嫌抄袭侵权/违法违规的内容,侵犯到您的权益，请在线联系站长,一经查实,本站将立刻删除。 本文来自网络,若有侵权，请联系删除，如若转载，请注明出处：https://yundeesoft.com/48965.html
